Instrument Cluster (Type C)

Instrument Cluster (Type C)



image

Speedometer. page 4-46

Tachometer page 4-46

Multi-information Display (Type C). page 4-47

Dashboard Illumination. page 4-50

Speedometer

The speedometer indicates the speed of the vehicle.

Tachometer

image

CAUTION

The tachometer shows engine speed in thousands of revolutions per minute (rpm).


Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.


image

*1

STRIPED

ZONE


*1

RED ZONE


*1 The range varies depending on the type of gauge.

NOTE

image

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.


Multi-information Display (Type C)

Multi-information Display (Type C)


INFO switch

image image

The multi-information display indicates the following information.

- Odometer

- Trip meter

- Engine coolant temperature gauge

- Fuel gauge

- Outside temperature

- Trip Computer

- Cruise Control Display

- Compass Display

image

Odometer, Trip Meter and Trip Meter Selector

The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the


image

Selector knob

Selector knob

Selector knob

Odometer


Press the selector knob Trip meter A

Press the selector knob Trip meter B

Press the selector knob

Odometer


Press the selector knob Trip meter A

Press the selector knob Trip meter B

Press the selector knob

Odometer


Press the selector knob Trip meter A

Press the selector knob Trip meter B

Press the selector knob

selector while one of them is displayed. The selected mode will be displayed.



Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The trip meter can record the total distance of two trips. One is recorded in trip meter A, and the other is recorded in trip meter B.


For instance, trip meter A can record the distance from the point of origin, and trip

meter B can record the distance from where the fuel tank is filled.


When trip meter A is selected, pressing the selector again within 1 second will change to trip meter B mode.


When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.


The trip meter records the total distance the vehicle is driven until the meter is again reset. Return it to “0.0” by depressing and holding the selector for 1 second or more. Use this meter to measure trip distances and to compute fuel consumption.

NOTE

- If TRIP A is reset using the trip meter when the function which synchronizes (resets) the fuel economy monitor and the trip meter (TRIP A) is on, the fuel economy data resets in conjunction with TRIP A.

Refer to Fuel Economy Monitor on page 4-113.

- Only the trip meters record tenths of kilometers (miles).

- The trip record will be erased when:

- The power supply is interrupted (blown fuse or the battery is disconnected).

- The vehicle is driven over 9999.9 km (mile).

Engine Coolant Temperature Gauge

Displays the engine coolant temperature. The white range of the gauge indicates that the engine coolant temperature is low,

image


and the red range of the gauge indicates that the engine coolant temperature is high and overheating.


image


image

CAUTION

If the engine coolant temperature gauge needle (white) flashes, there is a possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating on page 7-18.


NOTE

- (SKYACTIV-G 2.5T)

If the engine coolant temperature is high or the engine is hot, the engine output may be limited.

- The temperature unit (Centigrade/ Fahrenheit) of the engine coolant gauge display changes in conjunction with the temperature unit of the outside temperature display.

Refer to Personalization Features on page 9-11.

- During normal driving, the engine coolant temperature stabilizes at 100 °C (210 °F) or less, and the gauge indicates a range lower than 100 °C (210 °F).

Fuel Gauge

The fuel gauge shows approximately how much fuel is remaining in the tank when

the ignition is switched ON. We recommend keeping the tank over 1/4 full.


image

image

image

image

image

image

image

image

Full


image

image

image

1/4 Full

image image


image

image

image

image

image

image

image

image

Empty


image image

If the low fuel WARNING light illuminates or the fuel level is very low, refuel as soon as possible.

If inconsistency in engine performance or stalling occurs due to low fuel level conditions, refuel the vehicle as soon as possible and add at least 10 L (2.7 US gal, 2.2 Imp gal) of fuel.

Refer to Taking Action on page 7-33.

NOTE

- After refueling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

- The display indicating a quarter or less remaining fuel has more segments to show the remaining fuel level in greater detail.

image


image

- The direction of the arrow ( ) indicates that the fuel-filler lid is on the left side of the vehicle.

Dashboard Illumination

(Without auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the dashboard illumination is dimmed. (With auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the dashboard illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the dashboard illumination does not dim.

NOTE

- (With auto-light control)

When the ignition is switched ON in the early evening or at dusk, the dashboard illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

- When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

Refer to Headlights on page 4-75.

The brightness of the instrument cluster and dashboard illuminations can be adjusted by rotating the knob.

- The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

- The brightness increases by rotating the knob to the right.


image

Dim

Dim

Dim

Bright

Bright

Bright

Function for canceling illumination dimmer

The illumination dimmer can be canceled by rotating the dashboard illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

NOTE

- When the illumination dimmer is canceled, the instrument cluster cannot be dimmed even if the lights are turned on.

- When the illumination dimmer is canceled, the screen in the center display switches to constant display of the daytime screen.

Outside Temperature Display

When the ignition is switched ON, the outside temperature is displayed.


image


image

image


NOTE

- Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

- Significantly cold or hot temperatures.

- Sudden changes in outside temperature.

- The vehicle is parked.

- The vehicle is driven at low speeds.

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit. Settings can be changed by operating the center display screen.

Refer to Personalization Features on page 9-11.

NOTE

When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Trip Computer

The following information can be selected by pressing the INFO switch with the ignition switched ON.

- Distance-to-empty mode

- Average fuel economy mode

- Current fuel economy mode

- Compass mode

If you have any problems with your trip computer, consult an Authorized Mazda Dealer.

Distance-to-empty mode

This mode displays the approximate distance you can travel on the remaining fuel based on the fuel economy.


The distance-to-empty will be calculated and displayed every second.


image


image

image image


image

NOTE

- Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refueling is required, refuel as soon as possible if the fuel level is very low or the low fuel WARNING light illuminates.

- The display may not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

- The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge (indicating the remaining fuel supply) disappear.

- If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery cables are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Average fuel economy mode

This mode displays the average fuel economy by calculating the total traveled distance and the total fuel consumption since the vehicle was purchased or the past

image


data was reset. The average fuel economy is calculated and displayed every minute.


image


image

To reset the displayed past data, press the INFO switch for 1.5 seconds or longer.

After resetting the data, - - - L/100 km (- - - mpg) is displayed for one minute before the fuel economy is recalculated and displayed.

NOTE

If TRIP A is reset using the trip meter when the function which synchronizes (resets) the fuel economy monitor and the trip meter (TRIP A) is on, the displayed past data is reset.

Current fuel economy mode

This mode displays the current fuel economy by calculating the amount of fuel consumption and the distance traveled.


Current fuel economy will be calculated and displayed every 2 seconds.


image


image

When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) will be displayed.

Compass mode

image

The direction the vehicle is moving is displayed in one of eight directions while the vehicle is being driven.


image


image image


image


Display

Direction

N

North

S

South

E

East

W

West

NE

Northeast

NW

Northwest

SE

Southeast

SW

Southwest

Cruise Control Set Vehicle Speed Display

The vehicle speed preset using the cruise control is displayed.


image

Refer to Cruise Control on page 4-218.


WARNING/Indicator Lights

Instrument Cluster varies depending on model and specifications.

Instrument Cluster

image


Center of Dashboard


image


image

WARNING lights will appear in any of the highlighted areas


WARNING Indication/WARNING Lights

These lights turn on or flash to notify the user of the system operation status or a system malfunction.


Signal

WARNING

Page


image

Brake System WARNING Light*1*2

7-23



image image


ABS WARNING Light*1

Electronic Brake Force Distribu- tion System WARNING

7-23

ABS WARNING 7-26


image

Charging System WARNING Light*1

7-23


image

Engine Oil WARNING Light*1

7-23


image

Power Steering Malfunction Indicator Light*1

7-23


image

Master WARNING Light*1

7-26


image

Electric Parking Brake (EPB) WARNING Light*1

7-26


Signal

WARNING

Page


image

(Red)


Brake Pedal Operation Demand WARNING Light*1

Flashing 4-101

Buzzer & Flash- ing

7-26


image

Check Engine Light*1

7-26


image

*Automatic Transaxle WARNING Light*1

7-26


image

*AWD WARNING Light

7-26


image

Air Bag/Front Seat Belt Pretensioner System WARNING Light*1

7-26


image


*Tire Pressure Monitoring System WARNING Light*1

Flashing 7-26

Turns on 7-33


image

(Red)


KEY WARNING Light*1

Turns on 7-26

Flashing 7-33


image

LED Headlight WARNING Light*1

7-26


image

(Amber)


*Smart City Brake Support (SCBS) WARNING Light*1


7-33


image

Low Fuel WARNING Light

7-33


image

Check Fuel Cap WARNING Light*1


7-33


image

Engine Oil Level WARNING Light*1

7-33


image image

Seat Belt WARNING Light (Front seat)

7-33


image image image

(Red)


Seat Belt WARNING Light (Rear seat)


7-33


image

*Low Washer Fluid Level WARNING Light

7-33


image

Door-Ajar WARNING Light

7-33


*1 The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an Authorized Mazda Dealer.

*2 The light turns on continuously when the parking brake is applied.

Indication/Indicator Lights

These lights turn on or flash to notify the user of the system operation status or a system malfunction.


Signal

Indicator

Page


image image image

(Green)


Seat Belt Indicator Light (Rear seat)


2-30


image image

*Front Passenger Air Bag Deactivation Indicator Light*1

2-71


image

(Green)


KEY Indicator Light


4-5


image

Security Indicator Light*1

3-48


image

Wrench Indication/Indicator Light*1

4-56


image


Shift Position Indication


4-66


image

Lights-On Indication/Indicator Light

4-75


image


Headlight High-Beam Indicator Light

Headlight High-Low Beam

4-78

Flashing the Headlights 4-78



image image


Turn Signal/Hazard WARNING Indicator Lights

Turn and Lane-Change Signals

4-81

Hazard WARNING Flasher

4-89


image

(Green)


Brake Pedal Operation demand Indicator Light


4-97


image

AUTOHOLD Active Indicator Light*1

4-103


*Some models. 4-55


Signal

Indicator

Page


image


TCS/DSC Indicator Light*1

Traction Control System (TCS)

4-108

Dynamic Stabil- ity Control (DSC)

4-110

Turns on 7-26


image


*TCS OFF Indicator Light *1


4-108


image

*Select Mode Indication

4-117


image


*Blind Spot Monitoring (BSM) OFF Indicator Light*1

Malfunction 7-26

Except malfunc- tion

4-132


image

(Red)


*Smart City Brake Support (SCBS) Indicator Light


4-177


image


*Smart City Brake Support (SCBS) OFF Indicator Light*1


4-177


image

(White)


Cruise Main Indication


4-219


image

(Green)


Cruise Set Indication


4-219

*1 The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an Authorized Mazda Dealer.

image

Wrench Indicator Light When the ignition is switched ON, the wrench indicator light turns on and then

image turns off after a few seconds.

The wrench indicator light turns on under the following conditions:


image

- When the preset maintenance period has arrived.

- When it’s time to replace the engine oil.

Refer to Maintenance Monitor on page 6-16.

NOTE

- The wrench indicator light turns on earlier than the preset period depending on vehicle usage conditions.

- Whenever the engine oil is replaced, a reset of the vehicle engine control unit is necessary.

Refer to Maintenance Monitor on page 6-16.


image

Display

Display

Display

Dust-proof sheet

Dust-proof sheet

Dust-proof sheet

Optical receiver

Optical receiver

Optical receiver

Instrument Cluster (Type B)

(Page 81)

Instrument Cluster (Type B) ① Speedometer. page 4-30② Tachometer p...

Active Driving Display

(Page 83)

Active Driving Display* WARNINGWARNINGWARNINGAlways adjust the display brightness and position with the vehicle stopped:Adjustin

We also have owner's manuals for other vehicle years:

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car Mazda CX-5 you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!