Hazard Warning Flasher

Hazard WARNING Flasher

The hazard WARNING lights should always be used when you stop on or near a roadway in an emergency.


image


image


image

The hazard WARNING lights warn other drivers that your vehicle is a traffic hazard and that they must take extreme

CAUTION

when near it.


image image

Depress the hazard WARNING flasher and all the turn signals will flash. The hazard WARNING indicator lights in the instrument cluster flash simultaneously.

NOTE

- The turn signals do not work when the hazard WARNING lights are on.

- Check local regulations about the use of hazard WARNING lights while the vehicle is being towed to verify that it is not in violation of the law.



image

HomeLink Wireless Control System (Type A)*

HomeLink Wireless Control System (Type A)*

HomeLink Wireless Control System (Type A)*

NOTE

HomeLink and HomeLink house icon are registered trademarks of Gentex Corporation.

The HomeLink system replaces up to 3 hand-held transmitters with a single built-in component in the auto-dimming

mirror. Pressing the HomeLink button on the auto-dimming mirror activates garage doors, gates and other devices surrounding your home.


Indicator light

image

image

WARNING

HomeLink button



Do not use the HomeLink system with any garage door opener that lacks the safety stop and reverse feature:

Using the HomeLink system with any garage door opener that lacks the safety stop and reverse feature as required by federal safety standards is dangerous. (This includes garage doors manufactured before April 1, 1982.)

image


Using these garage door openers can increase the risk of serious injury or death. For further information, contact HomeLink at 1-800-355-3515 or www.homelink.com or an Authorized Mazda Dealer.

Always check the areas surrounding garage doors and gates for people or obstructions before programming or during operation of the HomeLink system: Programming or operating the HomeLink system without verifying the safety of areas surrounding garage doors and gates is dangerous and could result in an unexpected accident and serious injury if someone were to be hit.


NOTE

The programming will not be erased even if the battery is disconnected.

Pre-programming the HomeLink System


NOTE

It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal.

- Verify that there is a remote control transmitter available for the device you would like to program.

- Disconnect the power to the device.

Programming the HomeLink System


image

CAUTION

When programming a garage door opener or a gate, disconnect the power to these devices before performing programming. Continuous operation of the devices could damage the motor.

The HomeLink system provides 3 buttons which can be individually selected and programmed using the transmitters for current, on-market devices as follows:

1. Disconnect the power to the garage door opener or gate programmed to the hand-held transmitter.

2. Position the end of your hand-held transmitter 2.5―7.5 cm (1―3 inches) away from the HomeLink button you wish to program while keeping the indicator light in view.

3. Simultaneously press and hold both the chosen HomeLink and hand-held transmitter buttons. Do not release the buttons until step 3 has been completed.

NOTE

Some gate operators and garage door openers may require you to replace this Programming Step 2 with procedures

NOTE

d in the “Gate Operator/Canadian Programming” section.

4. After the HomeLink indicator light changes from a slow to a rapidly blinking light, release both the HomeLink and hand-held transmitter buttons.

image


NOTE

If the HomeLink indicator light does not change to a rapidly blinking light, contact HomeLink at www.homelink.com or call

1-800-355-3515 for assistance.

5. Connect the power to the garage door opener or gate programmed to the hand-held transmitter.

6. Firmly press and hold the programmed HomeLink button for five seconds, and then release it. Perform this operation two times to activate the door or gate. If the door or gate does not activate, press and hold the just-trained HomeLink button and observe the indicator light.

If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released.

NOTE

To program the remaining two HomeLink buttons, begin with “Programming”― step 1

If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with “Programming” steps 7―9 to complete the programming of a rolling code equipped device (most commonly a garage door opener).

7. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the

motor-head unit.

8. Firmly press and release the “learn” or “smart” button. (The name and color

of the button may vary by manufacturer.)

image

NOTE

Complete the programming within 30 seconds.

9. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the “press/hold/release” sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process.

HomeLink should now activate your rolling code equipped device.

NOTE

To program the remaining two HomeLink buttons, begin with “Programming”― step 1

For questions or comments, please contact HomeLink at www.homelink.com or

1-800-355-3515.

Gate operator/Canadian Programming

Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission ― which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.


If you live in Canada or you are having difficulties programming a gate operator by using the “Programming” procedures (regardless of where you live), replace


4-91


“Programming HomeLink” step 3 with the following:

NOTE

If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating.

Continue to press and hold the HomeLink button while you press and release ― every two seconds (“cycle”) your

hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. (The indicator light will flash slowly and then rapidly.)

Proceed with “Programming” step 4 to complete.

Operating the HomeLink System

Press the programmed HomeLink button to operate a programmed device. The code will continue being transmitted for a maximum of 20 seconds.

Reprogramming the HomeLink system

To program a device to HomeLink using a HomeLink button previously trained, follow these steps:

1. Press and hold the desired HomeLink button. DO NOT release the button.

2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with “Programming” - step 1.

Erasing Programmed HomeLink Buttons

To erase the existing programming from all three operating channels, press and hold the two outside buttons (image, image) on

the auto-dimming mirror until the HomeLink indicator light begins to flash after approximately 10 seconds.

Verify that the programming has been erased when you resell the vehicle.

image



image

HomeLink Wireless Control System (Type B)*

HomeLink Wireless Control System (Type B)*

HomeLink Wireless Control System (Type B)*

Horn

(Page 100)

Manual Climate ControlIndicator lightIndicator lightIndicator lightFully Automatic Climate Control Horn To sound the horn, press the mark...

HomeLink Wireless Control System (Type A)

(Page 102)

Hazard Warning Flasher ‌The hazard warning lights should always be used when you stop on or near a roadway in an emergency.The hazard warning li

We also have owner's manuals for other vehicle years:

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car Mazda CX-5 you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!