Light Bulbs

Light Bulbs


With xenon fusion headlights With halogen headlights



image

Luggage compartment light Rear map lights

Overhead light (Front)/ Map lights

image

Vanity mirror lights


Luggage compartment light Rear map lights

image

Overhead light (Front)/ Map lights

Vanity mirror lights



image

High-mount brake light

Front turn signal lights/Parking lights (Front side-marker lights)

Headlights (Low/High beam) Fog lights

Daytime running lights

Front turn signal lights/ Parking lights (Front side- marker lights)

Headlights (Low beam) Fog lights

Headlights (High beam)/ Day time running lights


Side turn signal lights


License plate lights Reverse lights

Taillights (Liftgate side)

Rear side-marker lights Rear turn signal lights Brake lights/Taillights

image


Some models.



image

WARNING

WARNING

WARNING

Do not replace the xenon fusion bulbs yourself:

Replacing the xenon fusion bulbs yourself is dangerous. Because the xenon fusion bulbs require high voltage, you could receive an electric shock if the bulbs are handled incorrectly. Consult an Authorized Mazda Dealer when the replacement is necessary.

Never touch the glass portion of a halogen bulb with your bare hands and always wear eye protection when handling or working around the bulbs:

When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is broken, it will explode and serious injuries could be caused by the flying glass. If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit.

Always keep halogen bulbs out of the reach of children:

Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way.

NOTE

β€’ To replace the bulb, contact an Authorized Mazda Dealer.

β€’ If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

β€’ Use the protective cover and carton for the replacement bulb to dispose of the old bulb promptly and out of the reach of children.

Replacing Exterior Light Bulbs

Headlights (With xenon fusion headlights)

Low/High beam bulbs

You cannot replace the low/high beam bulbs by yourself. The bulbs must be replaced at an Authorized Mazda Dealer.

Daytime running lights

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Lift the hood.

3. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector backward.


image

image


4. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight back out of the socket.


image

5. Install the new bulb in the reverse order of the removal procedure.

Headlights (With halogen headlights)

Low-beam bulbs, High-beam bulbs/ Daytime running lights

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Lift the hood.

3. (Right side)

image

Guide

Guide

Guide

Windshield washer fluid reservoir

Windshield washer fluid reservoir

Windshield washer fluid reservoir

Remove the windshield washer fluid reservoir from the guide.

4. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

Low-beam bulbs


image

High-beam bulbs/Daytime running lights


image

5. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.

image


Low-beam bulbs


image

High-beam bulbs/Daytime running lights


image

6. Install the new bulb in the reverse order of the removal procedure.

Front turn signal lights/Parking lights (Front side-marker lights)

1. Make sure the ignition is switched off, and the headlight switch is off.

2. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the right, and turn off engine. If you are changing the left bulb, turn the steering wheel to the left.

3. Pull the center of each plastic retainer and remove the retainers.


image

Removal

Removal

Removal

Installation

Installation

Installation

4. Turn the screw counterclockwise and remove it, and then partially peel back the mudguard.


image

5. Turn the socket and bulb assembly counterclockwise and remove it.

image


6. Disconnect the bulb from the socket.


image

7. Install the new bulb in the reverse order of the removal procedure.

image

Fog lightsΓ­

1. Make sure the ignition is switched off, and the headlight switch is off.

2. If you are changing the right bulb, start the engine, turn the steering wheel all the way to the right, and turn off engine. If you are changing the left bulb, turn the steering wheel to the left.

image

Removal

Removal

Removal

Installation

Installation

Installation

3. Pull the center of each plastic retainer and remove the retainers.

4. Turn the screw counterclockwise and remove it, and then partially peel back the mudguard.


image

image

5. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.


image


6. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight back out of the socket.


image

7. Install the new bulb in the reverse order of the removal procedure.

Side-turn signal lights

Due to the complexity and difficulty of the procedure, the LED bulbs must be replaced by an Authorized Mazda Dealer.

NOTE

LED bulb replacement is not possible because it is built into the unit. Replace the unit.

Brake lights/Taillights, Rear turn signal lights, Rear side-marker lights, Taillights (Liftgate side), Reverse lights

1. Make sure the ignition is switched off, and the headlight switch is off.

2. Remove the cover with a cloth- wrapped flathead screwdriver to the cover.

Brake lights/Taillights, Rear turn signal lights, Rear side-marker lights


image

Taillights (Liftgate side), Reverse lights


image


3. Turn the socket and bulb assembly counterclockwise and remove it.

4. Disconnect the bulb from the socket.

image


Brake lights/Taillights


image

Rear turn signal lights


image

Rear side-marker lights


image

Taillights (Liftgate side)


image

Reverse lights


image

5. Install the new bulb in the reverse order of the removal procedure.

High-mount brake light

Due to the complexity and difficulty of the procedure, the LED bulbs must be replaced by an Authorized Mazda Dealer.

NOTE

LED bulb replacement is not possible because it is built into the unit. Replace the unit.

License plate lights

1. Make sure the ignition is switched off, and the headlight switch is off.

image


2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with a flathead screwdriver.

3. Disconnect the bulb by pulling it out.


image

4. Install the new bulb in the reverse order of the removal procedure.


Replacing Interior Light Bulbs

image

Overhead light (Front)/Map lights, Rear map lights, Vanity mirror lightsΓ­

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.

2. Disconnect the bulb by pulling it out.

Overhead light (Front)/Map lights


image


image image

image

Rear map lights



Γ­Some models.

6-47

image



image


Vanity mirror lights


image

3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens unit by carefully prying on the edge of the lens unit with the flathead screwdriver.


image image

2. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.



image


image

CAUTION

CAUTION

CAUTION

When replacing the bulb always disconnect the connector first. Otherwise, electric and electronic devices could be shorted.

image


Tires

(Page 152)

Ø Be careful not to allow the rubber ring shown in the figure to be scratched or damaged.‌Ø If the rubber ring detaches, reattach it before inser...

Fuses

(Page 154)

3. Disconnect the bulb by pulling it out.‌4. Install the new bulb in the reverse order of the removal procedure. Fuses Your vehicle&#

We also have owner's manuals for other vehicle years:

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car Mazda CX-5 you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!